A BNC connector can look properly installed and still fail when the center pin is loose, the braid is trapped under the ferrule, or the wrong die compresses the sleeve. Knowing how to crimp BNC connectors correctly prevents intermittent camera feeds, video noise, signal loss, and expensive return visits. The job is straightforward, but connector style, cable size, and crimp-tool compatibility must match before the first cut.

Start With the Correct BNC Connector and Tool

BNC connectors are not universal. Before preparing the cable, verify the connector is made for the exact coax type being terminated. Common examples include RG59, RG6, RG58, RG174, and mini coax. A connector designed for RG59 may not grip RG6 correctly, even if it can be forced onto the cable.

Also confirm whether the installation requires a 50-ohm or 75-ohm BNC connector. CCTV and composite video systems generally use 75-ohm BNC connectors, while RF, test equipment, and many radio applications commonly use 50-ohm versions. The two styles use similar bayonet coupling, but their internal dimensions differ. For a short low-frequency run, a mismatch may appear to work. For a professional installation, use the specified impedance throughout the system.

Traditional crimp BNC connectors normally include a connector body, a center contact or pin, and a separate crimp ferrule. Some designs use a captive ferrule or a compression-style body. Follow the strip dimensions supplied for that connector series whenever available. Measurements vary by manufacturer, and using a generic strip length can leave the center conductor too short or expose too much braid.

You will need a coax cable cutter, a coax stripper set for the cable type, a compatible BNC crimp connector, and a ratcheting crimp tool with the correct die cavity. A continuity tester or coax cable tester is strongly recommended. Avoid using diagonal cutters or a utility knife for routine stripping. They can nick the center conductor or cut the braid unevenly, creating failures that are hard to spot later.

How to Crimp BNC Connectors Step by Step

1. Cut the coax square

Make a clean, square cut at the end of the cable. A crushed or angled cable end makes it harder to slide the ferrule and connector body into position. If the cable has been pulled tightly during installation, cut back to an undamaged section before terminating it.

Slide the crimp ferrule onto the cable first. This is easy to overlook, especially when working on a ladder, inside a cabinet, or above a ceiling. If the connector uses a separate ferrule and you forget this step, the connector must be removed and the cable end prepared again.

2. Strip the cable to the connector specification

Set the coax stripper for the strip lengths required by the connector. Most BNC crimp connectors need two exposed sections: a longer section where the outer jacket is removed to expose the braid, and a shorter section where the dielectric is removed to expose the center conductor.

After stripping, inspect the cable closely. The center conductor should be straight and clean, with no deep scoring or missing strands. The dielectric should have a clean, even edge. The braid should remain intact and extend evenly around the dielectric. Remove any loose foil fragments or stray braid wires before proceeding.

Foil-shielded cable requires extra care. Depending on the connector design, the foil may stay folded back with the braid or be trimmed as specified. Do not assume every connector handles foil in the same way. A connector made for dual-shield RG6 may have different preparation requirements than one designed for basic RG59 braid shield.

3. Prepare the braid without crossing the dielectric

Fold the braided shield back evenly over the outer jacket. The braid should lie flat around the cable, not bunch on one side. Make sure no braid strand touches the center conductor or extends across the exposed dielectric. One stray strand can create a short circuit or an intermittent fault when the cable is moved.

For high-density braid, use a small pick or pointed tool to open the braid gently rather than cutting aggressively. The goal is to preserve shielding coverage while making room for the connector body. If too much braid is removed, the ferrule may crimp on bare jacket instead of braid, weakening both the mechanical hold and the shield connection.

4. Install the center pin fully

Place the center pin onto the exposed conductor. Depending on the connector, the pin may crimp onto a solid center conductor, crimp onto a stranded conductor, or use a solder cup. This article addresses crimp-style contacts, but the connector instructions take priority if the pin is soldered or captive.

For a crimp pin, insert the conductor until it bottoms out in the pin. The conductor should be visible through the inspection hole, if the pin includes one. Position the pin in the proper die cavity and complete a full ratcheting crimp. Do not stop halfway through a ratcheting cycle. A complete crimp creates the required compression and reduces the chance of a pullout.

Inspect the contact after crimping. The pin should remain centered, the conductor should not protrude excessively from the front, and the crimp area should be compressed uniformly. If the pin spins freely or pulls off with light pressure, cut the cable back and start over.

5. Seat the connector body

Push the connector body onto the prepared cable until the center pin locks into place. Most BNC bodies provide an audible or tactile click when the pin engages, although this can be subtle. Check that the dielectric seats fully inside the connector and that the connector body reaches the intended position over the folded braid.

A common error is crimping the ferrule before the center pin is fully seated. The connector may still mate with equipment, but the contact can sit too far back and produce poor electrical performance. If the pin does not lock, do not force the ferrule. Remove the body, inspect the strip dimensions and pin position, then re-terminate with a new connector if needed.

6. Crimp the ferrule with the specified die

Slide the ferrule forward over the folded braid and connector body. Position it in the correct crimp die cavity. The die size must match the ferrule outside diameter, not simply the cable designation printed on the package. Connector manufacturers may use different ferrule dimensions for similar cable types.

Close the ratcheting crimper through a full cycle. The finished ferrule should show an even, controlled compression with no sharp splitting, severe deformation, or uncrimped gap. A hex crimp is common, but some connector systems use other profiles. Use the tool profile specified for that connector family.

Do not use pliers, vise grips, or an unmarked crimper as a substitute. They may hold the connector briefly, but they do not deliver consistent compression or proper shielding contact. This is especially risky on security camera runs where vibration, weather changes, or cable movement can turn a marginal termination into an intermittent service issue.

Inspect and Test Every Termination

Before connecting equipment, perform a quick mechanical inspection. Pull the connector firmly but reasonably. The cable should not slide inside the ferrule, and the connector body should not rotate independently of the cable.

Next, test electrical continuity. Verify continuity from center pin to center pin at the far end of the cable, and from shield to shield. Then verify there is no continuity between the center conductor and the shield. A basic multimeter can catch a short or open circuit. For longer CCTV, broadcast, RF, or data-over-coax runs, a cable tester or time-domain test method provides better fault isolation.

If the system carries analog video, look for rolling bars, ghosting, weak contrast, or intermittent picture loss after installation. On HD-over-coax camera systems, poor terminations may appear as unstable video, dropouts, or a camera that will not negotiate reliably. Replace questionable ends rather than trying to re-crimp a damaged ferrule. A new connector costs less than a troubleshooting call.

Common BNC Crimp Problems and Their Causes

A connector that pulls off usually points to the wrong ferrule die, incorrect cable diameter, insufficient braid under the ferrule, or an incomplete crimp cycle. A short between center and shield is usually caused by a stray braid strand or foil touching the center conductor. A connector that will not seat onto equipment may have a bent center pin, incorrect pin depth, or a body that was assembled before the pin locked.

Signal problems are more nuanced. The termination may pass a basic continuity test and still perform poorly because the connector impedance does not match the cable or system. This matters more as frequency rises and cable runs get longer. For standard composite CCTV, proper 75-ohm cable and connectors remain the correct choice. For RF and instrumentation, verify the cable and BNC series against the equipment specification instead of relying on appearance alone.

Keep Terminations Consistent Across the Job

For one-off repairs, it can be tempting to use whatever BNC connector and tool are available. For a new installation or recurring maintenance work, standardizing on a connector series, cable type, stripper setting, and crimp die saves time and produces more predictable results. Label the cable type and keep the approved strip dimensions with the termination tools.

A clean BNC crimp is not complicated, but it is a precision task. Match the connector to the coax, make clean strip cuts, keep the braid controlled, complete each crimp cycle, and test before closing walls or handing off the system. Those few checks keep a small connector from becoming the weakest point in the run.

← Older Post Newer Post →